Latest from my blog...

Subscribe to the RSS Feed

Want to Install Cabinets Perfectly? Get Pro Tips Here

Posted on 26 September 2019 by admin (0)

Are you looking for the change in your space and want to give a new look by installing cabinets? No worries to implement this assignment, here we are to guide you in installing cabinets. Our tips will head to install cabinets successfully.

 

Choosing cabinet designs is the most critical part also when you want that work with your current layout correctly. Installing new cabinets can help improve the emergence of the room and also provides you the additional storage space. Learn how to hang kitchen wall cabinets and install island cabinets with these below-mentioned tips.

 

  1. Plan your area and mark up on wall

The foremost step is to plan your space, and A standard, to-scale floor plan drawing will help for plotting out that exactly where you want to install wall cabinets. Along with planning, measurement is a crucial part. You have to measure from the highest point on the floor and mark a level line on the top of the base cabinets; the standard level is 54 inches from level. This will result in a proper cabinet installation with a good layout.

 

Label the location and Draw a vertical line for joining the edges of the first cabinet to be installed. Finally, mark the decided locations as you begin a how to install cabinets project.

 

  1. Position the first cabinet & remove the doors and knobs

Next step is to set cabinets 1/4 inch. From the marked line and chock, the base until the top side is even with the horizontal line and level from front to back. Drive 2-1/2-inch. Screw through the back into wall studs for anchoring. Meanwhile, remove all doors, handles, drawers, and knobs from the cabinets. It will assure the lightest possible load while hanging wall cabinets.

 

  1. Block large bows and Lift cabinets on the ledger board

It’s necessary to block all the bows in the wall properly before you hang the cabinets. If you don’t, it may accidentally pull the back off the cabinets while placing it on board. Check that cabinet are level and filled before moving on to the next step.

 

  1. Pre-drill, screw the cabinets & Use a Block of Wood for Scribing

Be sure to screw cabinets through the thick framing in the pre-drill process along the top of the cabinets. Pre-drill a 1/8-inch.hole before screwing cabinets together with a 2-1/2-inch. screws.

One more crucial point to notice here is to find the maximum distance between the wall and the outside of the cabinets. Take that measurement and make a pencil mark on your strip, Measure the distance from the wall to your pencil mark, make a scribing block of the same size. Use that block to trace a pencil line down the filler strip.

 

  1. Measure the gap cut & install the filler strip

Measure the gap between the wall and the ends of cabinets at the top and bottom. Add 1/16 inch to each measurement to draw a cutting line on the backside of a filler strip. Bracket the filler strip and cut it at a 10-degree angle from the backside. Test-fit the filler strip and set the piece in place, pre-drill and screw it to the cabinet frame when fits perfectly.

 

  1. Use 2x2s to Secure Cabinets to the Floor

This will help in raising cabinets to the flooring, Use blocks to represent the finished floor height, and Hold the blocks back a bit from the front, and it will be underneath the tile.

 

  1. Cut oversized holes and remove hardware

Cutting oversized holes of water lines and drain pipes might give you the impressive look of cabinets; also it makes it easier to slide and place cabinet in decided space. After installation of all cabinets successfully, remove all the undesired things and hardware from the area.

 

Learning how to install cabinets correctly is more straightforward than it might seem, to get the appealing look and perfect installation you need the right tools, some modest solid cabinets and a bit of effort. This way you can transform the look of your space its kitchen, bathroom or any other room in home or office.